Repair mortar

广告位

Repair mortar

Product features:

1. Dry-mix mortar products ensure the most important quality stability and bring matching performance with special requirements;

2. According to different repairs location, with targeted construction performance, ensuring good bonding to the base material even when working at high altitudes;

3. Low shrinkage, and the expansion coefficient of the plaster matches the base material, and the volume is stable ;

4. The special early strength formula can make the repair mortar have high strength in a short period of time and have high construction efficiency;

5. It has excellent adhesion to ensure the quality of repair;

6. Reduce carbon dioxide penetration and increase the durability of the repair surface;

7. Special anti-permeability and anti-corrosion formula can be used for repairing coastal buildings;

8. Non-toxic, in line with environmental requirements;

9. It can be used by adding water, simple and convenient;

10. The road repair formula is wear-resistant and prevents salt water from snow removal agents. Erosion;

11. The elastic modulus is lower than the surrounding concrete and has high strain resistance.

12. It has the characteristics of convenient construction, high early strength, no hollowing and cracking, etc. It is specially designed for repairing sandy floors and smoothing concrete floors.

2. Main performance:

Inspection items

Standard requirements

Test results

Compressive strength (Mpa)

≥its intensity level

≥its strength level

Shrinkage (%)

≤0.5

0.15

Water retention rate (%)

≥80

90

Layering (mm)

≤20

5.0

Usable time (h)

≥2

4-6

3. Construction technology:

Base layer treatment: The base material should be smooth, strong, clean, free of oil and dust, and use an interface Treatment agent treats the base surface.

Preparation: Add an appropriate amount of water to the dry powder repair mortar and mix evenly. The water-to-material ratio is about 1:4. Use clean water to mix the dry powder repair mortar evenly. Let it stand for 5 minutes and then stir it a little before use. No raw dough balls allowed.

IV. Construction method:

1. Surface treatment: Before construction, use a cutter to cut the repair area to an appropriate depth, remove all loose concrete, thoroughly remove rust, and Remove dust from the concrete surface and rinse with water. Although a water film does not necessarily form on the surface of the base material, it must be fully moistened with water before construction. Then the polymer-modified cement interface coating is applied to the steel surface layer, and an intermediate layer of repair mortar is applied before the coating is completely cured.

2. Stirring: Use a mechanical mortar mixer or a low-speed portable mixer to stir until the required consistency is reached. First add an appropriate amount of water, then start the mixer, and then gradually add this product to the water, continuing Stir for 5 minutes or until the ingredients are completely uniform and there are no lumps.

3. Construction: During construction, the repair mortar should be applied directly with a ash spoon or by hand and pressed onto the base surface of the coated interface layer. If the interface coating has dried before starting to apply the repair mortar, it must be completely removed and recoated before the repair mortar can be scraped until the repair is smooth.

4. Maintenance: After the construction is completed, the exposed surface needs to be cured. Suitable concrete curing agent (efficiency should be greater than 90%), wet sacks or continuous watering can be used for three days.

5. Notes:

The slurry mixed with water should be used up within 2 hours. The construction environment temperature is above 5℃. The repair mortar is alkaline and will irritate the skin. During use, avoid inhaling dust and contacting the skin and eyes, and wear appropriate protective gloves and eye protection. Once it comes into contact with skin, rinse with clean water. If it comes into contact with eyes, rinse immediately with plenty of water and seek medical treatment as soon as possible. This product is non-toxic and non-flammable.

6. Packaging and storage: This product should be moisture-proof and sun-proof. Each bag is 25kg and has a shelf life of three months. </p

广告位
This article is from the Internet, does not represent the position of Epoxy curing agent, reproduced please specify the source.https://www.dmp-30.vip/archives/28184

author:

Previous article
Next article
Contact Us

Contact us

+86 - 152 2121 6908

Online consultation: QQ交谈

E-mail: info@newtopchem.com

Working hours: Monday to Friday, 9:00-17:30, closed on holidays
Follow wechat
Scan wechat and follow us

Scan wechat and follow us

Follow Weibo
Back to top
Home
Phone
Products
Search