Epoxy curing agent Knowledge Covestro (formerly Bayer) Desmodur W H12MDI dicyclohexylmethane diisocyanate hydrogenated MDI HMDI 5124-30-1

Covestro (formerly Bayer) Desmodur W H12MDI dicyclohexylmethane diisocyanate hydrogenated MDI HMDI 5124-30-1

广告位

Covestro (formerly Bayer) Desmodur W H12MDI dicyclohexylmethane diisocyanate hydrogenated MDI HMDI 5124-30-1

Type

fat Cyclic diisocyanate monomer

Chemical description

Asia Methyl bis (4-cyclohexyl isocyanate) or dicyclohexylmethane diisocyanate or H12MDI

Molecular formula

OCN-C6H10-CH2-C6H10-NCO

Molecular weight

262

Equivalent

131

CASIndex number

5124 301

Purpose

Use For the preparation of polyisocyanates and polyurethanes


Product Specifications

Characteristics

Security                                                                                                     Because this product is an isocyanate monomer, special care must be taken when handling it.
This product safety information should be read carefully. It contains information on labeling, transportation, storage and product disposal, product safety and ecological impact. At the same time, please also pay attention to the supplementary data of the technical information. In addition, current national regulations governing the handling of polyisocyanates must be observed and followed.
In Germany, the maximum permissible concentration of Desmodur W for occupational exposure (sum of vapor and fumes) is 0.054 mg/m3 (based on 8-hour TWA). Do not exceed this limit, even for short periods of time. Remarks: H (= able to be absorbed through the skin) (TRGS00, October 2000).
In the UK, the maximum allowable concentration for incidental exposure (based on 8-hour TWA) of all isocyanates is 0.02 mg/m3. The maximum allowable concentration for short-term exposure (based on 10 minutes STEL) is 0.07 mg/cubic meter. This data is based on isocyanate content. In other countries, the maximum allowable concentration related to methylene bis-(4-cyclohexyl isocyanate) should be reported to Check with local authorities.
Avoid skin and eye contact with this product or inhalation of its vapor. Also avoid the formation of fumes, for example when cleaning mixing equipment with air flow or opening safety valves on pressurized vessels.
When handling Desmodur W products, protective gloves of different materials must comply with the following requirements:

Thickness

Penetration time

Butyl rubber-IIR

≥0.5

≥480 min

Fluorinated rubber-FKM

≥0.4

≥480 min

Nitrile rubber-NBR

≥0.35

≥480 min

Safety goggles, protective gloves and overall protective clothing must be worn. Contaminated clothing must be removed and disposed of immediately. When working under poor ventilation conditions, especially when handling a large number of open products, a gas mask must be worn (for a short period of time, a mask that can filter harmful gases can be worn; for a long period of time, when the protection conditions are poor) work, must be equipped with an assisted breathing system that can work independently).
If the odor of Desmodur W is smelled, it means that the maximum allowable air concentration has been exceeded, and the exposed area should be evacuated immediately.

For a long time, you can wear a mask that can filter harmful gases; for a long time, if you work under poor protection conditions, you must be equipped with an auxiliary breathing system that can work independently).
If the odor of Desmodur W is smelled, it means that the maximum allowable air concentration has been exceeded, and the exposed area should be evacuated immediately.

广告位
This article is from the Internet, does not represent the position of Epoxy curing agent, reproduced please specify the source.https://www.dmp-30.vip/archives/68492

author:

Previous article
Next article
Contact Us

Contact us

+86 - 152 2121 6908

Online consultation: QQ交谈

E-mail: info@newtopchem.com

Working hours: Monday to Friday, 9:00-17:30, closed on holidays
Follow wechat
Scan wechat and follow us

Scan wechat and follow us